1. Pre-Cleaning Preparation: Lay the Foundation for Effective Cleaning

1.1 Gather the Right Tools & Cleaners

•     Tools: Soft-bristled brooms, microfiber mops (avoid stiff-bristled or wire brushes), vacuum cleaners with hard-floor settings (no beater bars), clean microfiber cloths, plastic scrapers (for stubborn debris), and a bucket.
•     Cleaners: Neutral pH detergents (pH 6-8, e.g., mild dish soap or Dajulong’s specialized PVC floor cleaner), distilled water (to prevent mineral deposits), and isopropyl alcohol (for specific stains). Avoid acidic cleaners (vinegar, lemon juice), alkaline cleaners (bleach, ammonia), or abrasive cleaners (scrubbing powders), as they can corrode the flooring’s surface layer and damage its anti-slip and wear-resistant properties.

1.2 Assess the Flooring Condition

•     Check for loose debris, sharp objects, or gravel on the surface—these can scratch the floor during cleaning. Use a soft broom or vacuum cleaner to remove them first.
• Inspect for stubborn stains (e.g., oil, ink, food residue) and mark them for targeted treatment later.
• Ensure the flooring is fully cured (at least 72 hours after installation) before the first deep cleaning to avoid affecting the adhesive bond.

2. Daily Cleaning: Simple Steps to Maintain Basic Hygiene

2.1 Frequency

2.2 Step-by-Step Process

1. Use a soft-bristled broom or vacuum cleaner (hard-floor mode) to sweep away loose dust, hair, and debris from the entire area, paying special attention to corners, edges, and under furniture.
2. Prepare a cleaning solution: Mix 5-10ml of neutral detergent with 5 liters of distilled water (follow the detergent’s instructions for concentration). Avoid over-diluting (ineffective cleaning) or over-concentrating (residue buildup).
3. Wet the microfiber mop in the solution, then wring it thoroughly until it’s only slightly damp—excess water can seep into the flooring seams, causing warping or adhesive failure.
4. Mop the floor in straight, overlapping strokes, working from one end of the room to the other. For high-foot-traffic zones, repeat the mopping process to ensure cleanliness.
5. Allow the floor to air-dry naturally (usually 15-30 minutes). Avoid walking on it until it’s completely dry to prevent slips or residue from footprints.

3. Deep Cleaning: Restore Shine and Remove Embedded Dirt

3.1 Step-by-Step Process

1. Perform daily cleaning first to remove loose debris.
2. Prepare a slightly concentrated neutral cleaning solution (e.g., 10-15ml of detergent per 5 liters of water) or use Dajulong’s specialized composite PVC roll cleaner for optimal results.
3. Apply the solution to the floor in sections (10-15 square meters at a time) using a spray bottle or mop, and let it sit for 5-10 minutes—do not let it dry completely, as this can leave residue.
4. Use a soft-bristled brush or microfiber mop to gently scrub the surface, focusing on areas with heavy grime (e.g., entrance mats, cafeteria floors).
5. Rinse the floor thoroughly with clean distilled water using a damp mop to remove all detergent residue—residue can attract more dirt and make the floor slippery.
6. Dry the floor with a clean, dry microfiber cloth or turn on fans to speed up air-drying.

4. Targeted Stain Removal: Tackle Common Spills Effectively

4.1 Food & Beverage Stains (Coffee, Juice, Sauce)

• Blot the spill immediately with a dry microfiber cloth to absorb excess liquid—do not rub, as this can spread the stain.
• Apply a small amount of neutral detergent solution to the stain, let it sit for 2-3 minutes, then wipe clean with a damp cloth.
• For dried stains, gently scrape off the solid residue with a plastic scraper (hold at a 45-degree angle to avoid scratching), then clean as above.

4.2 Oil & Grease Stains (Cafeterias, Kitchens)

• Absorb excess oil with paper towels, then sprinkle a small amount of cornstarch or baking soda (non-abrasive) on the stain to absorb remaining grease—let it sit for 15-20 minutes.
• Vacuum up the powder, then wipe the area with a neutral detergent solution mixed with a drop of dish soap (for extra degreasing).
• Rinse with clean water and dry.

4.3 Ink & Marker Stains (Offices, Classrooms)

• For fresh ink: Blot with a dry cloth, then apply a small amount of isopropyl alcohol (70%) to a clean cloth and gently dab the stain—do not rub vigorously.
• For dried ink: Use a cotton swab dipped in alcohol to target the stain, then wipe with a neutral detergent solution to remove alcohol residue.
• Test alcohol on an inconspicuous area first to ensure it doesn’t affect the flooring’s color.

4.4 Water Stains & Mineral Deposits

• Wipe the area with a damp cloth soaked in distilled water to dissolve mineral deposits.
• For stubborn deposits, mix equal parts distilled water and white vinegar (use sparingly, as vinegar is acidic) and wipe gently—rinse immediately with clean water to neutralize.

5. Cleaning Taboos: Avoid These Mistakes to Protect Your Flooring

• Do not use abrasive tools: Stiff-bristled brushes, wire wool, or scouring pads can scratch the wear-resistant layer, reducing the floor’s durability and anti-slip performance.
• Do not use harsh chemicals: Acidic (vinegar, toilet cleaner), alkaline (bleach, ammonia), or solvent-based (paint thinner, acetone) cleaners can corrode the surface, discolor the floor, and break down the material structure.
• Do not use excessive water: Flooding the floor or leaving standing water can seep into seams, cause the flooring to warp, or damage the subfloor and adhesive.
• Do not wax or polish: Dajulong composite PVC roll flooring has a built-in shine—wax or polish can leave a sticky residue that attracts dirt and dulls the surface over time.
• Do not drag heavy furniture: Use furniture pads under legs to avoid scratching or indentations when moving furniture.

6. Conclusion: Extend Your Flooring’s Life with Proper Cleaning